Showing posts with label microdata. Show all posts
Showing posts with label microdata. Show all posts

Monday, August 8, 2022

Micro 5 brief history


Micro 5 was founded 





Micro Five trademark (TESS)  actual trademark for computer corp.

Trademark first used 1981, canceled 1991

Micro 5 trademark (TESS)  transferred and re-registered to another company


Digital Design Aug 81  Micro Five V-2000 terminal (pdf page 51) 

  1991 Samsung was importing systems as Micro Five.  judgement filed 1997



History (as I can recall)

Micro Five was founded (probably around 81) with Cliff Myers president,
staff including Alan Gauthrup, Dick Brown, Mike Bryga and Phil Mahru.

Phil and some of the others would later constitute the core Phoenix Bios
Irvine, Ca staff, and their start was here.

They came out with an 8086 multi user system with home grown software.

When the AT was announced they decided to make a clone.

Though nothing to do with Micro Five other than guys knew it was around
an XT sized board which would take copied 286 bios was developed in
Santa Ana, and was owned by a Taiwan corporation. 

They wanted a clean  room BIOS with hopefully no grounds to have to
worry about being sued by IBM.  They did develop their own bios and
a few other drivers, as they had the expanded memory.  Their design
for that wasn't IBM compatible, so they did their own memory driver.

Their product didn't take off as they were overrun by a host of such
systems.  But their systems turned out to be nice for system integrators
who needed more slots.  Eventually they came out with I think a 12 or
more slot product.  

They also I think had a 386 system as well. Eventually the server
product was the main product that was popular, and it was popular
with Novell server builders.  Samsung was really pushing hard into
that market, but not having the success they desired. 

Samsung acquired Micro 5 and their business and substituted in
Samsung hardware.  I don't recall if they'd started manufacturing it
prior to acquisition.

They ended up breaking up the manufacturing for systems not used
for servers, Server systems and service and eventually suspended
the brand for all intents and services.

FWIW, they also did the same sort of acquisition and eventual
shutdown of AST research, a much bigger system.  The overall
contraction that has left Dell, Lenovo, HP and a few other PC
makers had started, and AST didn't survive.

AST also never made any system liked as well as the original
Micro Five 286 and 386 servers.  They of course were eventually
eclipsed, but in their time there was a pretty sizable business.

As to drivers for the original 286 system, and their extended
memory, at the time there was a driver designed for the Intel
memory for the 286.  Interestingly DOS which was a very
dominant system at the time had a driver to access memory
up to 16mb.

What wasn't publicized was how Microsoft was running what
seemed to be a Real mode OS and accessing memory without
any extended hardware, paging, but seemed to be
accessing it in what was a new mode called protected mode.

That was significant because there was no documented way
to get a 286 back to real mode (1mb only) after you
placed the processor operating in the mode (Protected) to
access the extended memory.

There was no apparent hardware reset, which could
be used to force a return and continue to realmode.

What the Micro Five people had discovered was an undocumented
instruction that could reset the protected mode internal registers
without having to reset. 

A system reset would have been very long, and would have made
operating the peripheral controllers and a host of other
functions pretty difficult.  

But the instruction they independently discovered, and
used but refused to disclose was the Microsoft "LOADALL"
instruction, which Intel had not removed from the processor.

Originally designed to be a test feature, but not for release
it could load all the registers and the extended memory registers
that the 286 used for addressing the 16mb memory space.

A friend, Tom Roden also discovered and published
the functions of LOADALL, which outed the whole  trick, and a lot
of other people quickly incorporated it into their drivers.

--30--


Saturday, February 17, 2018

Microdata 1600 compatable parts






THIS PART CAME FROM A FULLY FUNCTIONAL, PERFECTLY RUNNING MIYANO JNC-35/45T CNC LATHE THAT WE DISMANTLED. WE HAVE THE VIDEO OF THE MACHINE RUNNING.

search ebay for miyano JNC-35/45T CNC

Cincinnati Milacron Acramatic clone of some sort

30

Monday, March 27, 2017

Microdata, Decision Data, and Western Dynex boards


These boards showed up in an auction and Al Kossow kindly directed my attention to the boards, sold after the system was scrapped.

There is a clean set of spares from a 2400 RPM Dynex, probably a 6000 drive, including backplane and terminator.

There is a Decision Data + Intel manufactured processor and memory set, as well as an 8 slot backplane in the lot.

And there is a Microdata manufactured 1600 board set in the lot, but with Decision Data markings in the etch and some of the silkscreens.  This includes a larger 14 slot backplane.

Included in the Microdata set, is a CPU set, DMA board set, 2950 (Decision Data badged), and one (or two) A20002613 8ways.  The 2613 had full modem control.

There is also an 8 port DB 25 board, which should work with any of the 8ways available, hopefully via ribbon cables.

There is an interesting cabling setup with an additional 50 pin connector on the 8 port connector that will have to be investigated.

Both of the backplanes are powered via molex connectors, rather than the Microdata Paddle board approach in the last slot.

Boards from Western Dynex 2400 RPM drive, probably 10mb capacity.

A2 Control

Tag says 2400RPM.  I am going to infer this was for a 10mb (5 over 5) drive, since I doubt many 5mb drives were made at 2400RPM

Closeup of service tag.  shows 2400RPM

Sector Counter A1

Servo A3

Data A4

Backplane, Pin side, showing Terminator and input cable slot

A1 Sector Counter / Control
A2 Control
A3 Servo
A4 Data
Backplane Component side.  Both sides have 3 level WW pins available on all pins

Set of boards in backplane, best guess as to location

Closeup of the shot with the boards in backplane
Only one board identified as Servo is pretty certain.  I guessed from memory on the others.
Closer shot of the boards in backplane

Decision Data processor set

8 Way connector Top 2 cables are probably from 2613.  not sure what the other one did





8 slot backplane.
Since there are no keyways in the backplane, and none on the 2901 cpu set boards, I'm guessing this is the backplane for the newer system.

Also it only hs the single 12 pin Molex power connection.  There is an 8 slot rear of board connector on the memory board below, probably to supply +5 and maybe a minus voltage to the memory array, so the backplane supply is probably enough +and- 12 to run the 2613's and a lot of +5 and ground

2901 cpu and firmware
Sadly one rom is missing, so no firmware disassembly is probably going to happen.
2910 and other logic in second CPU set board
A 40 pin chip / socket has been totally scraped off this, as well as maybe some other damage.  Worst damage of the lot.
Intel Memory board
The Etch shows Intel (in Intel font) made this board.  All the chips are NEC though.  Guess all the work making the board didn't pay off for the Intel memory division, unless they distributed or resold NEC parts.
Memory array on the Intel board
The array is of 16K x 1 parts, and there are 11 parts in each column.  Suggesting single bit correction 2 bit detection ECC capability with the memory.

Total of 64K, which would align with what a Microdata 1621 firmware board would do.
Memory chips with legible part#s
NEC UPD416C-2 parts  Date code 85 maybe on one chip?
NEC UPD416C-2  Link copied 3/2017
NEC UPD416C-2  PDF data sheet link copied 3/2017

200ns 16k x 1 memory Page Mode Dram

Microdata Compatable / manufactured (In*sight) boards

A20002613 8 way with modem control

Microdata A20002515 DMA board

Microdata A20001242 Control CPU board

Microdata A20001043 Data CPU Board

Second A20002613 8 way with modem control

A20001044-1 Front panel interface

14 slot backplane for Microdata CPU. 
From the spacing and practicality of the design, the 1040 front panel board goes in the slot on the left in the backplane.  Microdata had a 12 slot  with 20 amps, and an 18 slot with 40 amps (or 20) of their own.

Some outfit named Elko Pacific made these backplanes.  The connectors do not match the most common Microdata part for their original backplanes.  CDC originated the backplane connector that Microdata used.

This connector may be from a 130 pin connector vendor who made parts for the later Reality 6000's 8000s, and Royale systems.  The 1040 backplane had a heavier bakelite / plastic component.
Closeup of Elko Pacific badge and power input
Serial numbering didn't match the style of Decision data which used such as 111DDxxxx numbering

Also the backplane termination is shown.
This is serialed 6-05607

Closeup showing more etch info
Type A 18801434-2
also various other inspection stickers
111MD01001 is the Decision data style part number and appears to be possibly silkscreened on

Serial I/O DB-25 panel
Will to figure out if there is anything more than a multipurposing of the design to have the extra 50 pin connector.  The Microdata A20002613's would have used two 50 ribbon cables to the board.

Possibly another design board made by Decision Data used just a single 50 and omitted some signals.

When Microdata originally licensed the CPU to people, they had a single port RS232 with modem control board, a 4 way which had no scanner.

There were two 8 port boards with scanners, the 2612 and 2613.  The 2613 was designed by Bill Homans as one of his first projects.  Both of those boards had a scanner feature which was clocked around to present the status lines of each 8way to the software.  There was logic to "lock" the scanner when a line had a status change.  Ports could be disabled, in input listen and lock mode, or in interrupt driven output lock mode.

A single address starting @ 0x18 in the 1600 address space would control the board.  The board had one interrupt for the board, and usually used firmware assist to run the boards.

The original 1600 could run well with the later A20002614 and A20002615 designs, but did not do that well with the 2612 or 2613.

Microdata Reality used the 2614, 2615, and Irvine Computer Corp 80010001 8ways for I/O.

The 2614 and 2615 had only to have ground, transmit and receive to work.

The ICC 8way added flow control in and out in hardware with some additions of hardware to monitor the Reality I/O state.

Thursday, December 31, 2015

GIT notes for building and refreshing with bitbucket site


To update cloned repository, in the directory in question:

git pull origin master

To clone the directory, use

git clone master

Be sure to pull down subscriptions and subscribe to the notifications

SIMH example

https://github.com/simh/simh

git clone https://github.com/simh/simh.git